Navigation

  • Fishing Reports

  • Outdoor News
        - Business
        - Great Lakes
        - Great Plains
        - Northeast
        - Northwest
        - Rocky Mountains
        - Southeast
        - Southwest
        - Technology
        - Trophy Catches






    Recreational Real Estate

    Cabins for Sale
    Farms & Ranches
    Lakefront Properties
    Mountain Homes & Properties
    Riverfront Homes & Properties
    Other Recreational Properties


    Digg!







  • Wyoming Outdoor News



    PUTTING YOUR BOAT ON ICE
    Location: Wyoming


    Soon these glorious fall days will give way once again to another blustery Wyoming winter. If you've lived in this part of the country long, you've grown accustomed to winterizing just about everything in your life. Sandals get traded for snow boots, a new car ice scraper is purchased, fishing gear is cleaned and stowed away until next spring. But are you taking care of one of your more expensive investments?

    Don't forget about your boat when making preparations for winter. An afternoon of attention can do help prevent a spring full of problems. Here are some tips from the experts to make sure your craft remains seaworthy for next summer. As always, be sure to consult your boat's owners manual for specific guidelines and recommendations.

    Storage The best place for your boat to winter is out of the water, under cover and preferably in a climate-controlled environment, but most of us don’t have that luxury. Consider shrink-wrapping, or cover with a tarp or some other sturdy cover.

    Inboard Engine(s)

    You should run the engine(s) to warm it up and change the oil while it is warm. This tends to allow impurities to be drained away with the oil. You should also change the oil filter(s). Flush the engine(s) with fresh water. You should circulate antifreeze through the manifold by using a pickup hose from the waterpump to a bucket of antifreeze. Start the engine and allow the antifreeze to circulate until water starts to exit the exhaust. This process will vary slightly depending on your type of cooling system. While you're in the engine room you should also change the fluid in your transmission. Remove spark plugs and use "fogging oil" to spray into each cylinder. Wipe down the engine with a shop towel sprayed with a little fogging oil or WD-40.

    Stern Drive(s)

    You should thoroughly inspect the stern drive and remove any plant life or barnacles from the lower unit. Drain the gear case and check for excessive moisture in the oil. This could indicate leaking seals and should be repaired. Clean the lower unit with soap and water. If your stern drive has a rubber boot, check it for cracks or pinholes. Grease all fittings and check fluid levels in hydraulic steering or lift pumps. Check with your owner's manual for additional recommendations by the manufacturer.

    Outboard Engine(s)

    Flush engine with fresh water using flush muffs or similar device attached to the raw water pickup. Let all water drain from the engine. Wash engine down with soap and water and rinse thoroughly. Disconnect fuel hose and run engine until it stops. It is important to follow a step by step process to make sure that all fuel is drained from the carburetor to prevent build-up of deposits from evaporated fuel. Use fogging oil in the cylinders to lubricate the cylinder walls and pistons. Apply water resistant grease to propeller shaft and threads. Change the gear oil in the lower unit. Lightly lubricate the exterior of the engine or polish with a good wax.

    Fuel Fill your fuel tank(s) to avoid a build up of condensation over the winter months. Add a fuel stabilizer by following the instructions on the product. Change the fuel filter(s) and water separator(s).

    Bilges Make sure the bilges are clean and dry. Use soap, hot water and a stiff brush to clean up any oil spills. Once the bilges are clean, spray with a moisture displacing lubricant and add a little antifreeze to prevent any water from freezing.

    Fresh Water System Completely drain the fresh water tank and hot water heater. Isolate the hot water heater by disconnecting the in and out lines and connect them together. Pump a non-toxic antifreeze into the system and turn on all the facets including the shower and any wash-down areas until you see the antifreeze coming out. Also put non-toxic antifreeze in the water heater.

    Head Pump out the holding tank at an approved facility. While pumping, add fresh water to the bowl and flush several times. Use Vanish crystals or whatever your owner's manual recommends that will not harm your system and let sit for a few minutes. Again add fresh water and pump out again. Add antifreeze and pump through hoses, holding tank, y-valve, macerator and discharge hose. Again, check your owners manual to make sure that an alcohol-based antifreeze won't damage your system.

    Interior Once you have taken care of the system you should remove any valuables, electronics, lines, PFD, fire extinguishers, flares, fenders, etc. Over the winter these items can be cleaned, checked and replaced as necessary. Open all drawers and lockers and clean thoroughly. Turn cushions up on edge so that air is able to circulate around them or, better yet, bring them home to a climate controlled area. Open and clean the refrigerator and freezer. To keep your boat dry and mildew-free you might want to install a dehumidifier or use some of the commercially available odor and moisture absorber products.

    Out of Water Storage Pressure wash hull, clean barnacles off props and shafts, rudders, struts and trim tabs. Clean all thru-hulls and strainers. Open seacocks to allow any water to drain. Check the hull for blisters and if you find any that should be attended to you might want to open them to drain over the winter. While you're at it, why not give the hull a good wax job? It is probably best to take the batteries out of the boat and take them home and either put them on a trickle charger or charge them every 30-60 days.

    In Water Storage Close all seacocks and check rudder shafts and stuffing boxes for leaks, tighten or repack as necessary. Check your battery to make sure it is fully charged, clean terminals, add water if necessary and make sure your charging system is working. Check bilge pumps to ensure they are working and that float switches properly activate the pumps and that they are not hindered by debris. Make sure either to check your boat periodically or have the marina check it and report to you. If in an area where the water you are docked or moored in actually freezes, you should have a de-icing device or bubbling system around your boat.


    News Source: Wyoming G&FD - Oct. 21, 2008

    Comments
    There are no comments for this article.

    Be the first to comment here.

    «Back | News Home


    © 2017 AnglerGuide.com. All rights reserved.